Rebuilding with molly lub

[falzsf at mts.net (shawn f)]

ok sounds good, so i guess i will have to use ND50 if i can find it. I know i can get ND30....OK i will by some molly lub. Is there different thicknesses of it. I notice some guys said to make sure i dont get the thick stuff.
  ----- Original Message ----- 
  From: L F 
  To: shawn f ; ATS - Patrick Bureau 
  Cc: scirocco list 
  Sent: Friday, September 26, 2003 7:01 PM
  Subject: Re: Rebuilding with molly lub


  You won't find a non-detergent multi-grade motor oil, I don't think.  I believe all NDs are single grade.
  By the way, I would use assembly lube, not just motor oil.
  Larry
    ----- Original Message ----- 
    From: shawn f 
    To: ATS - Patrick Bureau 
    Cc: scirocco list 
    Sent: Friday, September 26, 2003 10:15 AM
    Subject: Re: Rebuilding with molly lub


    So using ND30 is fine. Good that was what i was planning on doing. I know i
    was told i should run ND20w50 for engine break in but i am having a hard
    time finding it. Anyideas? I live in winnipeg, manitoba, canada.

    Shawn F
    ----- Original Message ----- 
    From: "ATS - Patrick Bureau" <txrocco@sbcglobal.net>
    To: "Dan Bubb" <jdbubb@ix.netcom.com>; "shawn f" <falzsf@mts.net>; "scirocco
    list" <scirocco-l@scirocco.org>
    Sent: Friday, September 26, 2003 10:55 AM
    Subject: RE: Rebuilding with molly lub


    > the only lube an engine needs when rebuilding it is ND30 (non detergent 30
    > weight oil) I usually used 2 qtrs during rebuilds
    >
    >
    > ATS - Patrick Bureau - txrocco@sbcglobal.net
    > ----------------------------------------------
    > MSN:ATSGTX@hotmail.com |YAHOO:ATSGTX@yahoo.com
    > ICQ:32918816           |AIM:Texasscirocco
    > ----------------------------------------------
    >
    >
    > =>-----Original Message-----
    > =>From: scirocco-l-bounces@scirocco.org
    > =>[mailto:scirocco-l-bounces@scirocco.org]On Behalf Of Dan Bubb
    > =>Sent: Friday, September 26, 2003 10:32 AM
    > =>To: shawn f; scirocco list
    > =>Subject: Re: Rebuilding with molly lub
    > =>
    > =>
    > =>Definitely not on the pistons and rings (perhaps those should be
    assembled
    > =>dry?). I'd think it would be good most other places as long as it isn't
    > =>wheel bearing Moly lube. That would be a little heavy!
    > =>Dan
    > =>
    > =>----- Original Message -----
    > =>From: "shawn f" <falzsf@mts.net>
    > =>To: "scirocco list" <scirocco-l@scirocco.org>
    > =>Sent: Friday, September 26, 2003 10:49 AM
    > =>Subject: Rebuilding with molly lub
    > =>
    > =>
    > =>What does everyone think of rebuilding the engine with molly lube? If
    yes
    > =>where should i use it. I belive they say use iot on the top of
    > =>the cam caps
    > =>not sure where else though.
    > =>_______________________________________________
    > =>Scirocco-l mailing list
    > =>Scirocco-l@scirocco.org
    > =>http://neubayern.net/mailman/listinfo/scirocco-l
    > =>
    > =>
    > =>
    > =>_______________________________________________
    > =>Scirocco-l mailing list
    > =>Scirocco-l@scirocco.org
    > =>http://neubayern.net/mailman/listinfo/scirocco-l
    >
    >



    _______________________________________________
    Scirocco-l mailing list
    Scirocco-l@scirocco.org
    http://neubayern.net/mailman/listinfo/scirocco-l