Rebuilding with molly lub

[rocco16v at netzero.net (L F)]

You won't find a non-detergent multi-grade motor oil, I don't think.  I believe all NDs are single grade.
By the way, I would use assembly lube, not just motor oil.
Larry
  ----- Original Message ----- 
  From: shawn f 
  To: ATS - Patrick Bureau 
  Cc: scirocco list 
  Sent: Friday, September 26, 2003 10:15 AM
  Subject: Re: Rebuilding with molly lub


  So using ND30 is fine. Good that was what i was planning on doing. I know i
  was told i should run ND20w50 for engine break in but i am having a hard
  time finding it. Anyideas? I live in winnipeg, manitoba, canada.

  Shawn F
  ----- Original Message ----- 
  From: "ATS - Patrick Bureau" <txrocco@sbcglobal.net>
  To: "Dan Bubb" <jdbubb@ix.netcom.com>; "shawn f" <falzsf@mts.net>; "scirocco
  list" <scirocco-l@scirocco.org>
  Sent: Friday, September 26, 2003 10:55 AM
  Subject: RE: Rebuilding with molly lub


  > the only lube an engine needs when rebuilding it is ND30 (non detergent 30
  > weight oil) I usually used 2 qtrs during rebuilds
  >
  >
  > ATS - Patrick Bureau - txrocco@sbcglobal.net
  > ----------------------------------------------
  > MSN:ATSGTX@hotmail.com |YAHOO:ATSGTX@yahoo.com
  > ICQ:32918816           |AIM:Texasscirocco
  > ----------------------------------------------
  >
  >
  > =>-----Original Message-----
  > =>From: scirocco-l-bounces@scirocco.org
  > =>[mailto:scirocco-l-bounces@scirocco.org]On Behalf Of Dan Bubb
  > =>Sent: Friday, September 26, 2003 10:32 AM
  > =>To: shawn f; scirocco list
  > =>Subject: Re: Rebuilding with molly lub
  > =>
  > =>
  > =>Definitely not on the pistons and rings (perhaps those should be
  assembled
  > =>dry?). I'd think it would be good most other places as long as it isn't
  > =>wheel bearing Moly lube. That would be a little heavy!
  > =>Dan
  > =>
  > =>----- Original Message -----
  > =>From: "shawn f" <falzsf@mts.net>
  > =>To: "scirocco list" <scirocco-l@scirocco.org>
  > =>Sent: Friday, September 26, 2003 10:49 AM
  > =>Subject: Rebuilding with molly lub
  > =>
  > =>
  > =>What does everyone think of rebuilding the engine with molly lube? If
  yes
  > =>where should i use it. I belive they say use iot on the top of
  > =>the cam caps
  > =>not sure where else though.
  > =>_______________________________________________
  > =>Scirocco-l mailing list
  > =>Scirocco-l@scirocco.org
  > =>http://neubayern.net/mailman/listinfo/scirocco-l
  > =>
  > =>
  > =>
  > =>_______________________________________________
  > =>Scirocco-l mailing list
  > =>Scirocco-l@scirocco.org
  > =>http://neubayern.net/mailman/listinfo/scirocco-l
  >
  >



  _______________________________________________
  Scirocco-l mailing list
  Scirocco-l@scirocco.org
  http://neubayern.net/mailman/listinfo/scirocco-l