who's done a power window swap in MK2?

[rogercv1 at gmail.com (Roger)]

here are some pics I took of the fuse box.
<http://i177.photobucket.com/albums/w220/16vscirocco88/fuse%20box/Picture003.jpg>
<http://i177.photobucket.com/albums/w220/16vscirocco88/fuse%20box/Picture005.jpg>



On 4/6/07, John Lagnese <jlagnese@massed.net> wrote:
> I had decent panels from the donor.
>
> -----Original Message-----
> From: Lance LaPrarie [mailto:sciroccojunky@gmail.com]
> Sent: Friday, April 06, 2007 1:31 PM
> To: Roger
> Cc: Scirocco list
> Subject: Re: who's done a power window swap in MK2?
>
> what did you use to cut the switch holes in the door cards? I was
> thinking a
> cutoff wheel on my dremel. I have a set of door panels off the doner car
> but
> they are all leather and kind of beat. However, they have the correct
> holes.
> I was going to put tape on my manual ones and mark them with a sharpie.
>
>
>
>
> On 4/6/07, Roger <rogercv1@gmail.com> wrote:
> >
> > I plugged it in, I also had the full harness. did not want to splice
> > either.
> >
> > On 4/6/07, Lance LaPrarie <sciroccojunky@gmail.com> wrote:
> > > I would prefer to totally keep this harness intact where I don't
> have to
> > > splice in or anything. The car I pulled it from was fully
> functional. I
> > > pulled it and forgot where the two wires went. Also, there are a few
> > options
> > > as far as voltage goes on the back of the fuse panel. I didn't want
> to
> > just
> > > plug it in anywhere and risk a fire or short, etc......
> > >
> > > Did you just plug yours in or did you splice it? I'd think that just
> > > plugging it in would work since I didn't have to cut anything when I
> > took
> > > them off the donor car.
> > >
> > >
> > > On 4/6/07, Roger <rogercv1@gmail.com> wrote:
> > > > Ididi this swap a while back. I found a black and yellow plug on
> the
> > > > back of the fuse box loose and plugged the window harness to that.
> the
> > > > Battery I just followed the main battery cable to the fuse box and
> > > > used the open connections on the back of the fuse box next to the
> > > > battery cable.
> > > >
> > > > On 4/6/07, Lance LaPrarie < sciroccojunky@gmail.com> wrote:
> > > > > I've got the switched black and yellow wire and the red power
> wire.
> > > After
> > > > > looking at the bentley for a couple hours last night I couldn't
> > figure
> > > out
> > > > > where on the back of the fuse panel they go. Anyone know of
> where
> > the
> > > > > switched ignition wire goes and the appropriate power port are?
> It
> > would
> > > > > have been nice if they would have had a pic of the back with all
> the
> > > numbers
> > > > > and such to go off of. I need to get these in tonight since
> tomorrow
> > is
> > > the
> > > > > DCI bbq.
> > > > >
> > > > > Hook a brother up!!!
> > > > > _______________________________________________
> > > > > Scirocco-l mailing list
> > > > > Scirocco-l@scirocco.org
> > > > > http://neubayern.net/mailman/listinfo/scirocco-l
> > > > >
> > > >
> > >
> > >
> >
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
>