[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

End play



Shawn:
I noticed in your pictures you're pushing the crank back and forth with your
fingers to check end play.
Considering you have the crank all lubricated with some heavy oil/grease
it's fair to use a screwdriver to pry it back and forth.
Get some real force on it!
Dan

----- Original Message -----
From: "shawn f" <falzsf@mts.net>
To: <marc_scirocco@sympatico.ca>
Cc: "scirocco list" <scirocco-l@scirocco.org>
Sent: Sunday, September 28, 2003 10:06 PM
Subject: Re: End play


yeah i guess you dont have to sand very much at all right? Guess i will be
putting the crank in and out a few times!

----- Original Message -----
From: "marc_scirocco Qu?bec" <marc_scirocco@sympatico.ca>
To: "shawn f" <falzsf@mts.net>
Sent: Sunday, September 28, 2003 7:46 PM
Subject: RE: End play


> I sanded mine with 600 grit emery cloth with some oil. It takes patience,
> and clean EVERYTHING perfectly before final assembly.
>
> Have fun!
>
> Marc
> '83 Scirocco
> '88 Scirocco Slegato
>
> -----Message d'origine-----
> De : shawn f [mailto:falzsf@mts.net]
> Envoy? : dimanche 28 septembre 2003 20:40
> ? : marc_scirocco@sympatico.ca
> Objet : Re: End play
>
>
> awesome thanks...
> ----- Original Message -----
> From: "marc_scirocco Qu?bec" <marc_scirocco@sympatico.ca>
> To: "shawn f" <falzsf@mts.net>; "scirocco list" <scirocco-l@scirocco.org>
> Sent: Sunday, September 28, 2003 7:35 PM
> Subject: RE: End play
>
>
> > Yes, you sand bearing #3 to get proper crankshaft end play. If you sand
> too
> > much, they are available and cheap at the dealership (20$ cnd)
> >
> > Cheers.
> >
> > Marc
> > '83 Scirocco
> > '88 Scirocco Slegato
> >
> > -----Message d'origine-----
> > De : scirocco-l-bounces@scirocco.org
> > [mailto:scirocco-l-bounces@scirocco.org]De la part de shawn f
> > Envoy? : dimanche 28 septembre 2003 20:33
> > ? : scirocco list
> > Objet : End play
> >
> >
> > Well i assembled the crank into the main bearing and used white grease.
LD
> > said not too so i will take it apart and re assemble with the proper
> > assembly lubs, OOPS. Now i measure end play and it wasnt even .001 of
> > movement and it should be .0028 - .0067. So i guess i need to sand some
of
> > the side of bearing number 3. It is the one peice one. UI belive that it
> was
> > i do to increase the endplay. I have to push/pull pretting hard and dont
> > even get a thou.
> >
> > Just double checking this......
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
> >
> >
>
>
>



_______________________________________________
Scirocco-l mailing list
Scirocco-l@scirocco.org
http://neubayern.net/mailman/listinfo/scirocco-l