Flange pic and measurements

[Dan Bubb" <jdbubb@ix.netcom.com (Dan Bubb)]

I'm not Ron, but I'll butt in anyway.
No he doesn't need to install the springs with a Quaife and, as a matter of
fact, it isn't possible to install the springs with a Quaife.
Dan

----- Original Message -----
From: Allyn <amalventano@sc.rr.com>
To: <brian_wagner@sbcglobal.net>; Tobias >< <scirocco16v88@hotmail.com>;
<scirocco-l@scirocco.org>; Cheapass Ron Pieper <rapieper@yahoo.com>
Sent: Wednesday, March 19, 2003 11:56 PM
Subject: Re: Flange pic and measurements


> ok, tobias, you're golden
> ron, does he need to install the springs if he has a quaife?
> Al
>
> ----- Original Message -----
> From: <brian_wagner@sbcglobal.net>
> To: "Allyn" <amalventano@sc.rr.com>; "Tobias ><"
> <scirocco16v88@hotmail.com>; <scirocco-l@scirocco.org>
> Sent: Wednesday, March 19, 2003 11:39 PM
> Subject: Re: Flange pic and measurements
>
>
> > Just looked in the ETKA the following trannies used the factory LSD
> >
> > 2H,4k, 7A,4A, FK
> >
> > Good guess but in 83 they did use it.
> > ----- Original Message -----
> > From: "Allyn" <amalventano@sc.rr.com>
> > To: "Tobias ><" <scirocco16v88@hotmail.com>; <scirocco-l@scirocco.org>
> > Sent: Wednesday, March 19, 2003 10:27 PM
> > Subject: Re: Flange pic and measurements
> >
> >
> > > hmm, ah-ha! now i know what flange that is. that is a flange from a
> > factory
> > > lsd equipped 90mm flange housing. it must hold the spring in place of
> > where
> > > the old style seal would mate, so that housing (that that flange came
> > from)
> > > must have the larger seals, meaning when you stick that flange on the
> > > tranny, it should seal with the larger ring.
> > >
> > > but
> > >
> > > you are putting those flanges on a 2h, right?
> > > 2h trannies were made up to 83, and i dont think they equipped the
> factory
> > > lsd that far back, meaning that it should  have the smaller seals, and
> > > cannot properly seal against those flanges (they would seal against
the
> > > tapered part), requiring the green sleeve / larger seal mod.
> > > ...or you can be lucky, and the 2h had a factory lsd, meaning it has
the
> > > larger seals already. then its a drop in replacement.
> > > Al
> > >
> > >
> > > ----- Original Message -----
> > > From: "Tobias ><" <scirocco16v88@hotmail.com>
> > > To: <scirocco-l@scirocco.org>
> > > Sent: Wednesday, March 19, 2003 10:51 PM
> > > Subject: Flange pic and measurements
> > >
> > >
> > > >
> > > > Here are pics of the flange and measurements I just took:
> > > >
> > > > http://www.imaginehow.com/scirocco/post/flange1.jpg
> > > >
> > > > http://www.imaginehow.com/scirocco/post/flange2.jpg
> > > >
> > > > So, verdict?
> > > >
> > > > _________________________________________________________________
> > > > Add photos to your e-mail with MSN 8. Get 2 months FREE*.
> > > > http://join.msn.com/?page=features/featuredemail
> > > >
> > > >
> > > > _______________________________________________
> > > > Scirocco-l mailing list
> > > > Scirocco-l@scirocco.org
> > > > http://neubayern.net/mailman/listinfo/scirocco-l
> > >
> > >
> > > _______________________________________________
> > > Scirocco-l mailing list
> > > Scirocco-l@scirocco.org
> > > http://neubayern.net/mailman/listinfo/scirocco-l
> >
> >
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
>
>
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l