Euro bumper mounting question

[rfkellner@snet.net (Rick Kellner)]

I was looking for a source of euro bumper hardware and rebar parts.  I
have some bent parts that I would like to replace.  I suppose that I
could straighten them since the metal is relatively thin compared to the
US metal but I would like to at last investigate the cost of replacing
them.
Thanks,
Rick Kellner.

-----Original Message-----
From: scirocco-l-admin@scirocco.org
[mailto:scirocco-l-admin@scirocco.org] On Behalf Of Ryan H
Sent: Wednesday, January 29, 2003 10:22 PM
To: scirocco-l@scirocco.org
Subject: Re: Euro bumper mounting question

Particularly the Euro spec hardware?  Anyone know where to get it?
(Or Rick, did you mean you have some and you were asking me if I wanted
them?)

> Do you know where you can acquire new mounting hardware and rebar?

> Rick Kellner.
> -----Original Message-----
> From: scirocco-l-admin@scirocco.org
> [mailto:scirocco-l-admin@scirocco.org] On Behalf Of dale witt
> Sent: Wednesday, January 29, 2003 10:06 PM
> To: scirocco-l@scirocco.org
> Subject: Re: Euro bumper mounting question
> 
> You really need to replace the braces or have them straightened.  You
> will
> not be happy with the look unless they are perfectly aligned as the
euro
> bumper will show any offset much more than the US.
> 
> Dale Witt
> 82 and 86 16v Sciroccos
> 
> ----- Original Message -----
> From: "Lisa Lutman" <llutman@hotmail.com>
> To: <rhock99@epix.net>; <scirocco-l@scirocco.org>
> Sent: Wednesday, January 29, 2003 8:58 PM
> Subject: Re: Euro bumper mounting question
> 
> 
> > There is about half an inch or so on each side between the bumper
and
> the
> > body if I recall correctly.
> >
> >
> >
> > Lisa
> > Vancouver, BC
> > 87 2.0L 16V Scirocco
> >
> >
> >
> >
> >
> > From: Ryan H <rhock99@epix.net>
> > To: scirocco-l@scirocco.org
> > Subject: Euro bumper mounting question
> > Date: Wed, 29 Jan 2003 21:53:26 -0500
> >
> > My rear bumper is a bit crooked, i.e. the left side starts closer to
> the
> > front of the car than the right side does.  I believe the car may
have
> been
> > "bumped" from behind.  Is there adequate clearance with the Euro
> bumpers
> > that they could be mounted if the bumper mounts are a bit off?  Or
do
> you
> > think I could somehow straighten the bumper mounts?
> >
> >
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
> >
> >
> > _________________________________________________________________
> > The new MSN 8: advanced junk mail protection and 2 months FREE*
> > http://join.msn.com/?page=features/junkmail
> >
> >
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
> 
> 
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
> 
> 
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
> 


_______________________________________________
Scirocco-l mailing list
Scirocco-l@scirocco.org
http://neubayern.net/mailman/listinfo/scirocco-l