removal of fenders

[nealtovsen@yahoo.com (Neal Tovsen)]

> but please correct me if i'm wrong......anyone with
> 75-77 that's replaced
> their corner lights?

Yeah, me. Did you read my sig? :)

Worst case scenario: take out the whole headlight
assembly for that side. It's all on one bracket/plate
that bolts to the body. I think there are five screws,
and then it'll slide toward the center to clear that
lip. You'll probably have to remove the grille.

Neal

> 
> ------------------------------------
> Erik Seo
> Internet Media Specialist
> The Canyons Resort
> Park City, Utah
> 
> 
> 
> -----Original Message-----
> From: scirocco-l-admin@scirocco.org
> [mailto:scirocco-l-admin@scirocco.org]On Behalf Of
> Neal Tovsen
> Sent: Tuesday, May 14, 2002 8:19 AM
> To: Julie Macfarlane; seowitz@seowitz.com;
> scirocco-l@scirocco.org
> Subject: Re: removal of fenders
> 
> 
> Yeah, like everyone here has said:
> 
> 1) You shouln't need to remove the fender
> 
> 2) If you do, I used a torch to remove the rubber
> seam
> sealer from the rear attachment point on the fender.
> I'll add that there is also a bolt way up there on
> the
> top/back corner that is usually so deep under the
> rubber that you don't see it!
> 
> Neal
> '77 G60
> '88 16v
> 
> --- Julie Macfarlane <juliemac57@hotmail.com> wrote:
> > You shouldn't need to remove the fender. There
> > should just be 3 screws. 2 on
> > the outside of the rear face and on inner.Remove
> the
> > battery, then pull the
> > rubber cover back. The light is held in with a
> > plastic tab.
> > Then just remove the screws.
> >
> > GL
> >
> > Julie
> >
> >
> > >From: "Erik Seo" <seowitz@seowitz.com>
> > >To: <scirocco-l@scirocco.org>
> > >Subject: removal of fenders
> > >Date: Tue, 14 May 2002 01:12:50 -0600
> > >
> > >Well i'm just full of questions!
> > >
> > >I just got a new front left turn signal for my 77
> > rocco....
> > >ok so it seems that I need to remove my fender to
> > get the thing in
> > >there.....
> > >
> > >So after looking at the Bentley, I removed all
> the
> > screws along the engine
> > >bay, the one by the grille, the two bottom one's,
> > removed the bumper
> > >screws,
> > >and then the two in the wheel well on the door
> side
> > of the wheel well.  As
> > >far as what I could see, and what the Bently
> manual
> > said that's it.
> > >
> > >Problem is, the damn thing wouldn't move......am
> I
> > missing something?
> > >
> > >Erik
> > >www.seowitz.com
> > >www.team-arg.com
> > >
> > >
> > >
> > >
> > >_______________________________________________
> > >Scirocco-l mailing list
> > >Scirocco-l@scirocco.org
> > >http://neubayern.net/mailman/listinfo/scirocco-l
> >
> >
> >
>
_________________________________________________________________
> > Chat with friends online, try MSN Messenger:
> > http://messenger.msn.com
> >
> >
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
> 
> 
> =====
> ~Neal
> 
> __________________________________________________
> Do You Yahoo!?
> LAUNCH - Your Yahoo! Music Experience
> http://launch.yahoo.com
> 
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
> 


=====
~Neal

__________________________________________________
Do You Yahoo!?
LAUNCH - Your Yahoo! Music Experience
http://launch.yahoo.com