chronic intermediate shaft seal failure

[pb3vr6 at yahoo.com (Tonee Northam)]

I thought they renamed it the Boomerang for obvious reasons.
 
But, when they do workout the many virus in years to come, were buying one.
 


David Utley <fahrvegnugen@cox.net> wrote:


v\:* {behavior:url(#default#VML);}o\:* {behavior:url(#default#VML);}w\:* {behavior:url(#default#VML);}.shape {behavior:url(#default#VML);}
Doorag, dude, the doorag…  J

 

David

 

-----Original Message-----
From: Tonee Northam [mailto:pb3vr6@yahoo.com]
Sent: Saturday, October 23, 2004 10:08 PM
To: David Utley; Doug C.; Scirocco List
Subject: RE: chronic intermediate shaft seal failure

 

Removing the engine!

 

Sounds like light bulb replacement on a Phaton, or is that Beetle?

 



David Utley <fahrvegnugen@cox.net> wrote:

If you can move that shaft up or down more than a mouse wisker, then yeah I think the bearings are indeed worn. And that is bad news, as the only way to replace them is by removing the engine...

Sorry to hear of your bad luck... :(

David

-----Original Message-----
From: scirocco-l-bounces@scirocco.org [mailto:scirocco-l-bounces@scirocco.org]On Behalf Of Doug C.
Sent: Saturday, October 23, 2004 2:58 PM
To: Scirocco List
Subject: Fwd: chronic intermediate shaft seal failure

Upon further inspection, it does appear to be leaking from where the seal contacts the shaft. I've also noticed there is bit of play (wiggle) in the intermediate shaft. Have the bearings gone bad causing it to leak at the seal?
Thanks again...

-Doug
>-----Original Message-----
>From: Doug C. [mailto:carvsdriver@msbx.net]
>Sent: Saturday, October 23, 2004 02:46 PM
>To: 'Scirocco List'
>Subject: chronic intermediate shaft seal failure
>
>a few weeks ago, the little keyway on the intermediate gear shaft sheared off and took ou the seal with it, producing a good size oil leak. Well I replaced the seal, put everything back together again, and it still leaked at the exact same spot. So, I replaced the seal again today, and it is still leaking in the same spot. 
>
>Am I missing something here, or could the seal carrier be bad? It is actually leaking along the outside edge of the seal where it contacts the seal carrier, not the inside edge that seals on the shaft.
>
>oh, motor is a 1.8l 16v
>
>TIA!
>
>-Doug 
>
>
>
>_______________________________________________
>Scirocco-l mailing list
>Scirocco-l@scirocco.org
>http://neubayern.net/mailman/listinfo/scirocco-l
>






_______________________________________________
Scirocco-l mailing list
Scirocco-l@scirocco.org
http://neubayern.net/mailman/listinfo/scirocco-l


_______________________________________________
Scirocco-l mailing list
Scirocco-l@scirocco.org
http://neubayern.net/mailman/listinfo/scirocco-l


 

Elmhurst, IL.

93' Corrado VR6 (Baby) 
00' Rabbit GTI GLX VR6 (Sleeper) 
00' Plymouth Voyager SE (Wife's Winter Driver) 
94' Passat GLX VR6 (Now Jarrett's Newer B3) 
*****Rice, Marinated and Grilled Daily By German Engineered Weber Grill*****



Elmhurst, IL.
93' Corrado VR6 (Baby) 
00' Rabbit GTI GLX VR6 (Sleeper) 
00' Plymouth Voyager SE (Wife's Winter Driver) 
94' Passat GLX VR6 (Now Jarrett's Newer B3) 
*****Rice, Marinated and Grilled Daily By German Engineered Weber Grill*****